Media-tech MT4206 Guía de instalación

1 WLAN USB Adapter Welcome ...

10 Step 2: Please insert the AUTORUN CD into your CD-ROM drive. The CD should auto-start, displaying the following window. If it does not start, cli

11 Step 3: Click " Next ". Step 4: Click " Next ".

12 Step 5: Click " Install ". Step 6: Click " Finish ".

13 Windows 2000 Step 1: As Windows starts it will detect that new hardware has been added, and start the " Found New Hardware Wizard ". C

14 Step 2: Please insert the AUTORUN CD into your CD-ROM drive. The CD should auto-start, displaying the following window. If it does not start, cli

15 Step 3: Click " Next ". Step 4: Click " Next ".

16 Step 5: Click " Install ". Step 6: Click " Finish ".

17 Making a Basic Wireless Network Connection For Windows XP users, your native Windows XP wireless support (Wireless Zero Configuration Service) ha

18 Step 2: Click the " Available Network " button to scan available access points.

19 Step 3: Double click on the SSID of AP that you are going to connect to and create profile that

2 Welcome Thank you for purchasing the IEEE 802.11n WLAN USB Adapter. WLAN USB Adapter has an extra foundation which is designed to make WLAN USB Ada

20 you are connecting to an open (Encryption is None) wireless network for example the SSID is 11n_AP_Router. Step 4: Click the " OK ".

21 Step 6: Now you are ready to use the Wireless Network to Internet or intranet.

22 Note: This example is an open wireless network. If you are going to connect to a Wireless adapter with security protection, you

23 settings in this profile to be corresponding to the other wireless adapter. Please click on the " Network Authentication " drop-down lis

24 Introduction to the Wireless LAN Utility Note: This management instruction uses Windows XP as the presumed operation system. Some functions are n

25 General After starting the utility, the general page pops up This General tab provides the information of your current wireless network connectio

26 Profile The Profile tab lists the preferred connections. You can click the buttons beside to do configure each connection. Functions Add To ad

27 Available Network This Available Network tab lists the reachable wireless network. Functions Refresh To rescan available Wireless Networks. Ad

28 Status The Status tab shows the current connection status.

29 Statistics The Statistics tab shows the transmission activity record. Clicking the " Reset " button recounts the values from zero.

3 WLAN USB Adapter Overview WLAN USB Adapter has the USB interface, LED and WPS button below. Interface USB Interface: Connect the USB Interface to

30 Wi-Fi Protected Setup (WPS) An easy and secure setup solution for Wi-Fi network.

31 Push Button Config (PBC) Method If both AP and users’ Wireless LAN Utility has the physical button or visual button of Push Button Config (PBC),

32 Step 2: Click on " Push Button Config (PBC) " button.

33 Step 3: Now you are ready to use the Wireless Network to Internet or intranet.

34 PIN Method 2 If AP know users’ PIN code and the PIN code is 87489095, please follow steps below to complete the WPS. Step 1: Double click the

35 Step 2: Click on " Pin Input Config (PIN) " button. Step 3: Click on " Yes " button.

36 Step 4: Select the desired WPS AP Name and then click on " Select " button. Step 5: Please enter the PIN Code into your AP.

37 Step 6: Now you are ready to use the Wireless Network to Internet or intranet.

38 Uninstall Step 1: Click " Start -> All Programs -> REALTEK 11n USB Wireless LAN Utility -> Uninstall ". Step 2: Click "

39 Step 3: Click " Finish ".

4 WLAN USB Adapter Installation The following instructions will guide you to through the process of installing the WLAN USB Adapter. Windows Vista

40 Troubleshooting Session Overlap If there is more then one AP on the PBC mode, there will be [Session Overlap].Please using PIN method or wait for

41 REALTEK 11n USB Wireless LAN is Disconnected If you see the message below, please refer to the chapter Making a Basic Wireless Network Connection

5 Step 2: Please insert the AUTORUN CD into your CD-ROM drive. The CD should auto-start, displaying the following window. If it does not start, click

6 Step 3: For Security reasons VISTA requires the installer program to have administrator priviledges so the new policy called " User Account Co

7 Step 5: Click " Next ". Step 6: Click " Install ".

8 Step 7: Click " Finish ". Step 8: Click " Finish ".

9 Windows XP Step 1: As Windows starts it will detect that new hardware has been added, and start the " Found New Hardware Wizard ". Clic